E Studio 161 Printer Driver Download Latest

By cognitive d.

E Studio 161 Printer Driver Download Install Update

Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law.

User safety This Toshiba digital plain paper copier does not produce laser radiation hazardous to the user. It is certified as a Class 1 laser product under the U. The fusing area is hot. Exercise care in this area when removing misfed paper. Doing so may damage your eyes. To get full use of all machine features, be sure to familiarise yourself with this manual and the machine.

AB series metric and inch series references Both specifications are quoted where applicable. Page 15, step First-Copy time may vary depending on the power-supply voltage, ambient temperature, and other operating conditions. Parallel connector Connect to your computer to use the printer function. Holds up to 40 originals.

Original guides when the ADF is installed Adjust to the size of the originals. The indicator lights up when the machine is online, and goes off when the machine is off-line. The indicator blinks while the machine is receiving print data and while printing is paused. It will take about 45 seconds for the machine to warm up. Before using special paper, contact your authorized service representative.

Loading the paper tray Gently lift and pull out the paper tray until it stops. Push the pressure plate down until it locks in place. Envelopes Do not use the following envelopes, as misfeeds will occur. Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper, and move the left guide to the appropriate slot as marked on the tray. Grasp the locking knob on the guide and slide the guide to the indicator line of the paper to be loaded.

If "Auditing mode" has been enabled p. Copying from the ADF Make sure that an original has not been left on the document glass. Adjust the original guides to the size of the original s. Set the original s face up in the document feeder tray. This function automatically adjusts the copy image according to the original being copied.

If you wish to select the exposure level yourself, follow the steps below. Select from two original types and five exposure levels for each original type. The exposure level used in automatic exposure adjustment can also be changed. A maximum of copies factory default setting can be set. The indicator of the selected ratio will light up. Reduction only in the horizontal direction. Copying originals A and B onto each side of one sheet of paper Copy original A. This feature is convenient for making copies of books and other dual page originals on individual sheets of paper.

When the other job is finished, the copy run will resume using the original copy settings. Interrupt copying is not possible when the user programs are being configured. A computer can be connected to these connectors to use the machine as a printer. To use the machine as a printer, the printer driver must first be installed as explained in the "Printer Driver Setup Guide". The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption.

To switch between toner save mode and high image quality mode, follow the steps below. Paper tray factory default. The display shows "- -" with the left hyphen blinking.

Enter the program number with the numeric keys. In "Auditing mode", the display shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for copying.

Auditing mode program No. Resetting account program No. If no account numbers have been established, the error code "15E" will appear in the display.

Many problems can be easily resolved by the user. If you are unable to solve the problem using the troubleshooting guide, turn off the power switch and unplug the machine, and contact your authorized service representative. Problem The machine does not operate. Copies are too dark or too light. Part of the image is cut off or there is too much blank space. Original size not selected automatically. When the ADF is installed. Cause and solution Misfeed occurs. The paper is outside of the specified size and weight range.

Paper curled or damp. Problem Copies are smudged or dirty. White or black lines appear on copies. Paper size for a paper tray cannot be set. A copy job stops before it is finished. Any one of the alarm indicators is lit or blinking. Problem Printing is slow. The printed image is light and uneven. The printed image is dirty. The printed image is skewed or it runs off the paper. Removing the software If you need to remove the software, follow these steps.

Steadily Developer is required. Contact your authorized service representative. Steadily Replacement of toner cartridge will be needed soon. Open the feeding roller cover and remove the misfed original from the document feeder tray. Close the feeding roller cover. Section C Remove the misfed original from the exit area.

If the misfed original cannot be easily removed from the exit area, open the moveable part of the document feeder tray and remove the original. If the misfed paper is visible here, go to "C.

Misfeed in the transport area". If paper is misfed here, go to "A. Misfeed in the paper feed area". Misfeed in the fusing area Gently pull on the top center of the front cover to open. Turn the roller rotating knob in the direction of the arrow. Roller rotating knob Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal.

Misfeed in the transport area Open the fusing paper guide by pressing down the projection on either side of the guide and remove the misfed paper. Be careful not to tear the misfed paper during removal. The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Check and Remove the misfed paper. Lift and pull out the upper paper tray and remove the misfed paper. Grasp the handle to open the lower side cover. Remove the misfed paper. Obtain a new cartridge.

When the toner cartridge replacement required indicator cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below. When the toner cartridge replacement indicator Note Gently pull on the top center of the The total output count is all pages for both printing and copying printed by the machine and the total output count can be counted up to , Always keep these parts clean.

E Studio 161 Printer Driver Download

Drivers & Software

Posted by Anonymous on Jul 12, Driver can be download via below link: Posted on Jul 14, I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two. Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Toshiba e-STUDIO161 Operator's Manual

E Studio 161 Printer Driver Download

Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. User safety This Toshiba digital plain paper copier does not produce laser radiation hazardous to the user. It is certified as a Class 1 laser product under the U. The fusing area is hot.

0 thoughts on “E Studio 161 Printer Driver Download

Leave a Reply

Your email address will not be published. Required fields are marked *